●KCB齒輪泵性能范圍

  流量：1.1m3/h-600m3/h壓力：0.28MPa--2.5MPa  Traffic: 1.1 m3 / h - 600 m3 / hpressure: 0.28 MPa, 2.5 MPa

  主要用于油田、油庫、港口、碼頭、船舶等大流量輸油，卸油！Mainly used in oilfields, oil depot, ports, docks, ship big flow like oil, oilunloading

  應用范圍:KCB/2CY型齒輪輸油泵適用于輸送粘度在300c.s.t以下的各種油類，如原油、柴油、潤滑油、動植物油等。配用銅齒輪可輸送低閃點液體，如汽油、苯等。介質溫度不超過70℃，耐高溫油泵的使用溫度不超過300℃。本泵身帶有安全閥，超載時起安全作用。軸封有骨架油封、機械密封、填料密封三種型式，訂貨注明。KCB齒輪潤滑泵主要用于各種機械設備中的潤滑系統中輸送潤滑油，適用于輸送粘度在10oE（75c.s.t）以下，溫度在300℃以下的具有潤滑性的油料，不銹鋼齒輪泵可輸送食用油料、飲料等。軸封有骨架油封、機械密封、填料密封三種型式.Scopeof application: KCB type / 2 cy gear oil pump is suitable forconveying viscosity at 300 c. S.t under various oil, such as crudeoil, diesel oil, lubricating oil, animal and plant oil. With coppergear can handle liquid low flash point, such as gasoline, benzene,etc. Medium temperature does not exceed 70 ℃, the use of high temperature resistant oil pumptemperature does not exceed 300 ℃. Whenthe pump body with a safety valve, overloading security role. Shaftseal skeleton oil seal, mechanical seal, packing three type,indicate the order. KCB gear lubrication pump is mainly used forall kinds of mechanical e of conveying lubricating oil inthe lubricating system, suitable for conveying viscosity in 10 oe(below 75 c. S.t), the temperature is below 300 ℃with lubrication oil, stainless steel pump cantransport edible oil, beverage and so on. Shaft seal skeleton oilseal, mechanical seal, packing three types.

 ●KCB齒輪泵安裝說明:

　　1、安裝泵的地點應足夠?qū)挸?，以方便檢修工作。2、泵安裝的好壞，對泵的平穩運行和使用壽命有很重要的影響，所以安裝校正工作必須仔細地進行，不得草率行事。3、泵吸入管的安裝高度、長度和管徑應滿足計算值，力求簡短，減少不必要的損失（如彎頭等）；并保證泵在工作時，不超過其允許汽蝕余量。4、吸入和排出管路應該有支架。泵不允許承受管路的負荷。KCBgear pump installation instructions: 1, the location of theinstallation of pump should be spacious enough, to facilitatemaintenance and repair work. The stand or fall of 2, pumpinstallation, for the smooth running of the pump and service lifehave very important influence, so the installation calibration workmust be carried out carefully and must not be too hasty. 3,installation height of pump suction pipe, the length and diametershould satisfy the calculated value, to short, reduce unnecessarylosses, such as elbow, etc.); And ensure the pump at work, no morethan the allowed NPSH. 4, suction and discharge line should be asupport. Pump are not allowed to bear load of pipeline.

●KCB齒輪泵概述

　　KCB齒輪油泵在輸油系統中可用作傳輸、增壓泵；KCB gearoil pump in the oil system can be used as a transport, boosterpump;

  在燃油系統中可用作輸送、加壓、噴射的燃油泵；In the fuel system can beused as a transport, pressure, jet fuel pump;

  在一切工業領域中，均可作潤滑油泵用。In all industrial areas, canbe used as lubricating oil pump.

  KCB齒輪泵主要有齒輪、軸、泵體、安全閥、軸端密封所組成。齒輪經熱處理有較高的硬度和強度，與軸一同安裝在可更換的軸套內運轉。泵內全部零件的潤滑均在泵工作時利用輸出介質而自動達到。KCBgear pump are mainly gear, shaft, pump body, valve, shaft end seal.Gear after heat treatment with high hardness and strength, andshaft installed in the replaceable shaft sleeve. In all parts ofthe lubrication pump are pump work automatically to achieve usingthe output media.

  泵內有設計合理的泄油和回油槽，是齒輪在工作中承受的扭矩力Zui小，因此軸承負荷小，磨損小，泵效率高。Pump is the drainage and back into the groove of reasonabledesign, is a gear in the work under the minimum torque force, sothe bearing load is small, wear small, pump with highefficiency.

  泵設有安全閥作為超載保護，安全閥的全回流壓力為泵額定排除壓力的1.5倍，也可在允許排出壓力范圍內根據實際需要另外調整。但注意本安全閥不能作減壓閥的長期工作，需要時可在管路上另行安裝。從主軸外伸端向泵看，為順時針旋轉。Pumpis e with safety valve as overload protection, the totalreflux pressure relief valve is rated pump out pressure of 1.5times, also can allow discharge pressure range according to actualneeds and adjust. But note that this cannot be a long-term workpressure reducing valve, relief valve can be installed in thepiping shall be separately when necessary. To pump from the mainshaft overhang end to see, for clockwise.

●kcb齒輪泵的結構：KCB gear pumpstructure:

　　泵主要有泵體、齒輪、軸、軸承、安全閥、前蓋、后蓋、密封部件、聯軸器部件組成。設有安全閥的泵、當排油管路的液壓值超過泵的規定時，安全閥開啟，保證泵及原動機不致因壓力過高而受到損壞。軸端密封有三種形式：填料密封、機械密封、橡膠圈密封，用戶可根據具體的使用條件選擇合適的密封結構。泵有良好的自吸性，泵內運動部件利用輸送的液體實現潤滑，致工作時可以不加引液和潤滑劑。Mainlyinclude pump body, pump gear, shaft, bearing, relief, front cover,back cover, sealing parts, clutch parts.Is e with safetyvalve pump, when the discharge of oil pipeline hydraulic valueexceeds the rules of the pump, relief valve open, ensure the pumpand prime mover from damaged because the pressure was toohigh.Shaft end seal has three forms: packing seal, mechanical seal,rubber ring seal, the user can choose according to the specificconditions of use suitable sealing structure.Good self-primingpump, pump inside the moving parts using conveying fluidlubrication, can not add lead to work fluid andlubricant.

●kcb齒輪泵安裝: KCB gear pumpinstallation:

　　1、泵安裝前應檢查泵和電機在運輸過程中是否受到損壞，如電機是否受潮，泵的進出口防塵蓋是否損壞而使污物進入泵腔內等。1,before the pump installation, should check the pump and motor isdamaged during the transit, whether be affected with damp beaffected with damp such as motor, pump the import and export ofdust cover for damage and make the dirt into the pump chamber,etc.

　　2、泵在搬運過程中，應選擇合適起吊位置，減少泵的變形。2,pump in the process of handling, should choose appropriate liftingposition, reduce the deformation of the pump.

　　3、泵的底座應固定在牢固的基礎上，以免產生振動影響泵的正常工作。3, the base of the pump should be fixed on the basis of thestrong, so as to avoid vibration influence the normal work of thepump.

　　4、泵的進出口管路應清理干凈不得存有硬顆粒的報告雜物。4,import and export of pipeline of pump should be cleaned up shallnot have the report of hard particles sundry.

　　5、管路口徑一般不小于泵的進出口徑，進油管路應盡量短，并減少?gòu)澛?。必要時在進油口安裝金屬過濾器，過濾器的有效面積不應小于管道過流面積的三倍。5,pipe diameter is generally not less than the in and out of thecaliber of pump, the oil pipeline should be short, as far aspossible and less detours.When necessary, metal filter is installedon oil inlet filter effective area should not be less than threetimes of pipe flow area.

　　6、安裝時，不得用泵來承擔管路的重量。7、用手轉動聯軸器，泵應轉動靈活，不得有過緊或輕重不均現象，如有應立即排除。

6, when installation,must not use the pump to bear the weight of the line.7, turn thecoupling with the hand, the pump should be flexible rotation, cannot have too tight or weight uneven phenomenon, should immediatelyruled out.

●KCB齒輪泵安裝順序: KCB gear pumpinstallation order:

　　 1、在安裝過程中，為防止雜物落入機器內，機組的所有孔眼均應蓋好。1, during the installation process, so as to prevent debrisinto the machine, all perforation should cover of theunit.

　　2、在接好管路及確定電動機轉動方向后，再接上聯軸器，并再校核一遍軸的同心度。2, good on the line and determine the direction of motorrotation, and coupling is connected, check it again and shaftconcentricity.

　　3、校正泵軸和電機軸的同心度，在聯軸大路外圓上，允許偏差0.1毫米；兩聯軸器平面的間隙應保證2～4毫米，（小泵取小值）間隙要均勻，允差0.3毫米。3, calibration of pumpshaft and motor shaft concentricity, cylindrical, along the road incoupling allowable deviation of 0.1 mm;In the plane of the twocoupling gap should guarantee 2 ~ 4 mm, small little pump (invalue) clearance wants even, tolerance of 0.3 mm.

　　4、將機組放在埋有地腳螺栓的基礎上，在底座與基礎之間，用成對的楔墊用校正用。4, put the unit in buried with anchor bolt, on the basis ofbetween the base and foundation, with pairs of wedge cushion withcorrection.

　　5、為防止管線中雜物進入泵內，對新安裝的管線，在泵膠應裝設過濾器，其有效截面應大于吸入管截面的2～3倍。5,in order to prevent debris into the pump in the pipeline, pipelineof new installation glue should be installed in the pump filters,the effective cross section should be greater than the suction pipesection 2 ~ 3 times.

　　6、松開聯軸大，用水平儀分別放在泵軸和底座上，通過調整楔墊，校正機組水平，適當擰緊地腳螺栓，以防走動。6,loose coupling, use level on the pump shaft and base, respectively,by adjusting the wedge cushion, correction unit level, tighten theanchor bolts, just in case.

　　7、在機組實際試運行2～3小時后，作Zui后檢查，如無不良現象，則認為安裝合格。

7, in the actualcommissioning unit 2 ~ 3 hours later, a final inspection, if thereis no negative phenomenon, is considered tion.