重慶市紅螞蟻塑業有限公司
聯系人：潘銀潔
手機 ：
電話 ；023-68689303
傳真 ；023-68689302
QQ ；1157564052
E-mail；[email protected]
網址 ；www.21spc.net
地址 ；重慶市九龍坡區西彭鎮西南國際塑料城13幢附16號
主營業務：【經營業務】
通用塑膠原料：ABS、PP、PS
工程塑膠原料：PC、PC/ABS、POM、PBT、PA6、PA66、PPA
主要品牌：
德國道默,上海聚威，SABIC，中國臺灣南亞，中國臺灣長春，韓國可隆，浙江俊爾
SABIC? PC Resin PC0703R
Asia Pacific: COMMERCIAL
PC0703R resin is a low flow (MFR = 7 at 300?C/1.2kg), heat and UVstabilized, polycarbonate product with mold release designed foruse in the extrusion
market. It is available exclusively atwww.sabicpc.com
TYPICAL PROPERTIES? TYPICAL VALUE Unit Standard
MECHANICAL
Tensile Stress, yld, Type I, 50 mm/min 63 MPa ASTM D638
Tensile Strain, yld, Type I, 50 mm/min 6 % ASTM D638
Tensile Strain, brk, Type I, 50 mm/min >70 % ASTM D638
Tensile Modulus, 50 mm/min 2350 MPa ASTM D 638
Flexural Stress, yld, 1.3 mm/min, 50 mm span 90 MPa ASTM D790
Flexural Modulus, 1.3 mm/min, 50 mm span 2300 MPa ASTM D790
Hardness, Rockwell R 120 - ASTM D 785
Tensile Stress, yield, 50 mm/min 63 MPa ISO 527
Tensile Strain, yield, 50 mm/min 6 % ISO 527
Tensile Strain, break, 50 mm/min >70 % ISO 527
Tensile Modulus, 1 mm/min 2350 MPa ISO 527
Flexural Stress, yield, 2 mm/min 90 MPa ISO 178
Flexural Modulus, 2 mm/min 2300 MPa ISO 178
Hardness, Rockwell R 120 - ISO 2039-2
IMPACT
Izod Impact, unnotched, 23°C NB J/m ASTM D 4812
Izod Impact, notched, 23°C 900 J/m ASTM D 256
Instrumented Impact Energy @ peak, 23°C 65 J ASTM D3763
Izod Impact, unnotched 80*10*3 +23°C NB kJ/m? ISO180/1U
Izod Impact, unnotched 80*10*3 -30°C NB kJ/m? ISO180/1U
Izod Impact, notched 80*10*3 +23°C 70 kJ/m? ISO180/1A
Izod Impact, notched 80*10*3 -30°C 12 kJ/m? ISO180/1A
(1) Typical values only. Variations within normal tolerances arepossible for various colors. All values are measured after at least48 hours storage at 23°C/50% relative humidity. All properties,except the melt volume and melt flow rates, are measured oninjection molded samples. All samples tested under ISO teststandards are prepared according to ISO 294.
Source GMD, last updated:
Visit www.sabicpc.com for additional information about SABIC? PCresins.
(2)Only typical data for selection purposes. Not to be used forpart or tool design.
(3)This rating is not intended to reflect hazards presented by thisor any other material under actual fireconditions.
(4)Internal measurements according to ULstandards.
(5)Measurements made from laboratory test coupon. Actual shrinkagemay vary outside of range due to differences in processingconditions, e, part geometry and tool design. It isrecommended that mold shrinkage studies be performed with surrogateor legacy tooling prior to cutting tools for new moldedarticle.
(6)Needs hard coat to consistently pass 60 sec VerticalBurn.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASICINDUSTRIES CORPORATION (SABIC) OR ITS SIDIARIES OR AFFILIATES (SELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD
CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATIONAND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOODFAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION,WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THISDOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TOTHE
EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATINGSELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESSOTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FORANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS,SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.Each user isresponsible for making its own determination as to the suitabilityof Seller s materials, products, services or recommendations forthe user s particular use through appropriate end-use and othertesting and analysis. Nothing in any document or oral statementshall be deemed to alter or waive any provision of Seller sStandard Conditions of Sale or this Disclaimer, unless it isspecifically agreed to in a writing signed by Seller. Statements bySeller concerning a possible use of any material, product, serviceor design do not, are not intended to, and should not be construedto grant any license under any patent or other intellectualproperty right of Seller or as a recommendation for the use of anymaterial, product, service or design in a manner that infringes anypatent or other intellectual property right.
SABIC and brands marked with ? are trademarks of SABIC or itssubsidiaries or affiliates.
? 2016 Saudi Basic Industries Corporation (SABIC).